703.15 Open-Hearth, Electric Arc Furnace, and Basic Oxygen Furnace Steel Slag Aggregate Used for Items 410, 411, and 617. When using surface applications OH, EAF, and BOF slag, ensure that the slag meets the aging and stockpiling, deleterious substances, and crushing requirements of 703.14. Recycled OH, EAF, or BOF slag from Department or non ...

Unit Weight The total (wet) unit weight of soils, see Table 1, can be estimated from typical values, or measurements of mass and volume can be performed on Shelby tube samples or California or Modified California rings. Moisture content can provide the necessary data for calculating the dry unit weight of …

sand, gravel, and crushed stone. Aggregates 101 - Common Aggregates in PA Aggregate sieves used to separate material by size (gradation). passes through a 4" screen½ inch or 12.5mm sieve visible on right. (by weight) of the material can be retained on that sieve, so 1/2021 Open graded (left) -versus - Well graded (right)

This table has in-truck and placed densities. SO a crushed gravel is about 1.43 T/cy in the truck and 1.85 T/cy placed, typ. They note that placed density varies from 1.7 to 1.9 T/cy, with the lower end of the range for materials with say 40% sand and the upper end for more open-graded ballast.

Crushed stone (DGA - dense grade aggregate, QP - quarry process, shoulder stone) Rocks crushed and graded by crusher and screeners. Widely used for roads and driveways. Fine gravel: Gravel with particles between 2 and 4 millimeters. Lag gravel: Surface accumulation of coarse gravel produced by the removal of finer particles. Pay gravel

The density of pure water is also 62.4 lbs/cu.ft (pounds per cubic foot) and if we know that ammonium nitrate has a sg of 0.73 then we can calculate that its density is 0.73 x 62.4 = 45.552 lbs/cu.ft.

Use field or quarry stone of approved quality. Stone may be certified from a source previously approved. Ensure that maximum dimension does not exceed four times the minimum dimension. 901.02.01 Stone for Riprap. Ensure that stone for riprap is uniformly graded from the smallest to the largest pieces as specified in the Contract Documents.

measure) unit weight of at least 70 pounds per cubic foot in accordance with MTM 123. B. Crushed Concrete Coarse Aggregate. Use Department-owned concrete on the project to produce crushed concrete coarse aggregate. The Contractor may use crushed concrete coarse aggregate in the following

Dense graded aggregate (DGA), also referred to as well-graded aggregate or quarry process, is stone that has been crushed through a series of crushers and screened through a sieve. Although some individual stones in the mix are ¾" in size, the product is bound together with smaller stone particles and stone dust, resulting in maximum weight ...

Crushed Stone Grade 1-10. Generally, as the grade number goes up, the size of the stone goes down. #1 – The # 1 crushed stone grade is the largest of the crushed stone grades and includes stone between 2-4 inches long. This material is great for larger jobs or for filling in larger holes. #3 – This size of the stone ranges from 1/2 to 2 ...

Conversion Chart. The following is a guideline of conversion factors for quoted material. Lorusso Corporation does not guarantee quantities or yields. This conversion is based on material as loaded in truck bodies. The Lorusso Corporation sales policy for material is factored by the ton and is billed accordingly. Material. Conversion: Tons / C.Y.

This mixture combines limestone, trap rock, granite, crushed rock, sand, and stone dust. It's also known as crusher run, quarry process, #411 gravel, road stone, or dense grade aggregate. Crushed Limestone Cost. Crushed limestone costs $30 to $38 per ton, from $1.59 to $2.00 per square foot, or between $35 and $54 per yard.

Coarse Graded Dense Graded 2 5 8 9 11 12 431 91 531 731 4 in. (100 mm) 3½ in. (90 mm) 2½ in. (63 mm) 100 2 in. (50 mm) 80-100 1½ in. (37.5 mm) 100 100 100 1 in. (25 mm) 0-25 85-98 100 70-90 100 80-100 100 ¾ in. (19 mm) 0-10 60-85 75-95 100 50-70 70-90 90-100 ...

Dense Graded Base (¾ inch) Our dense graded base, also known as star pac or crusher run, is a combination of stone dust and ¾ inch crushed stone. This product is suitable as a base layer under a patio or a walkway, extra parking areas, driveways, under concrete slabs, and asphalt.

F:Truck Body Pricing & BrochuresExcelCubic_Yardage_Chart DCubic_Yardage_Chart D Rev A 6/9/2015 AGGREGATE TYPE

Section 815—Graded Aggregate 815.1 General Description This section includes the requirements for material to be used for base, subbase, or shoulder course material, and includes graded aggregate, unconsolidated limerock base, and crushed concrete base. 815.1.01 Related References A. Standard Specifications Section 800—Coarse Aggregate

This crushed stone comes in a wide range of sizes. So how much does a yard of gravel weigh? The weight of gravel depends on the type and density or grading. In most cases, a cubic yard of gravel weighs between 2,400 to 2,900 pounds (1,088 to 1,315 kg).

"A dense graded base aggregate, produced by crushing, washing and screening high calcium or dolomitic limestone. A white to light gray colored sedimentary rock formed by the precipitation of calcium carbonate from sea water. The particles are sized from 1 1/2" (37.5mm) to zero (dust)."

Dense graded aggregate (DGA), also referred to as well-graded aggregate or quarry process (QP), is stone that has been crushed through a series of crushers and screened through a sieve. Although some individual stones in the mix are 1 ½" in size, the product is bound together with smaller sized stones, stone particles and stone dust ...

aggregate base course density The most recent Aggregate Base Course (ABC) unit weight test results performed by the NCDOT M&T Soils lab can be queried using this page. Use the drop down boxes to select the company and/or quarry submitting the sample.

Design with a dense-graded, crushed stone base — A typical grid pavement installation con-sists of compacted soil subgrade, a dense-graded base of com-pacted crushed stone, 1/2 to 1 in. (13 to 25 mm) thick bedding sand, and grids. The openings in the grids are filled with topsoil and grass (Figure 15), or aggregate (Figure 16).

(a) Subbase of Gravel. Only uniformly graded gravel from the pit shall be used. The Contractor shall manipulate the material in the pit to eliminate non-uniformly graded pockets of material. (b) Subbase of Crushed Gravel. When stockpiling, care shall be taken to prevent segregation in the pile. (c) Subbase of Dense Graded Crushed Stone.

minimum of 85% crushed particles and at least two faces resulting from fracture. Stone - a piece of rock quarried and worked into a specific size and shape for a particular purpose. PennDOT requires that stone be durable and free from slate texture or cleavage planes. Sand – Mined or manufactured rock particles predominately smaller than 3/16".

Construction Aggregate Calculator. Enter the width, length, thickness, and product density and hit the "Calculate" button to calculate your estimate. If you do not know the product density, use the optional density estimator* or contact a local sales representative.

Crushed stone density is variable ranging from 2.4 - 2.7 Metric Tons per cubic Meter depending on the type of stone, the stone crushing machinery, and how the …

Mass, Weight, Density or Specific Gravity of Bulk Materials. The density of pure water is also 62.4 lbs/cu.ft (pounds per cubic foot) and if we know that ammonium nitrate has a sg of 0.73 then we can calculate that its density is 0.73 x 62.4 = 45.552 lbs/cu.ft.

the ASTM Method D 2049 (Relative Density), the Washington Spring-Loaded Vibratory Compactor Method, the Marshall Hammer Test, and the Gyratory Compactor Procedure. The aggregates tested were a granite-gneiss, a crushed gravel, a dolomitic limestone, and a basalt. A prototype field compaction 'testing program was conducted using the same

Materials: Aggregate (crushed stone or gravel and manufactured sands), asphalt binder (with modifiers) Information: Open-graded HMA can be more expensive per ton than dense-graded HMA, but the unit weight of the mix when in-place is lower, which partially offsets the higher per-ton cost. The open gradation creates pores in the mix, which are ...

Aggregate (crushed stone or gravel and manufactured sands), asphalt binder (with modifiers) Mix Design. Less structured than for dense-graded or SMA mixes. Open-graded mix design generally consists of 1) material selection, 2) gradation, 3) compaction and void determination and 4) asphalt binder drain-down evaluation.

Tile. 2970. 1.43. Trap stone. 5849. 2.52. Most of Harmony Sand & Gravel's products will weight approximately 2,840 pounds per cubic yard or about 1.42 tons per cubic yard. For estimating purposes, most Contractor's consider the yield to be 3,000 pounds per cubic yard or 1.5 tons per cubic yard.

We think you will agree when we say that guessing how many pounds of crushed stone your landscaping construction will require is not easy. Estimating by eye is ineffective and can result in you wasting time and money purchasing unnecessary amounts of material.

About Stone, crushed; 1 cubic meter of Stone, crushed weighs 1 602 kilograms [kg] 1 cubic foot of Stone, crushed weighs 100.00959 pounds [lbs] Stone, crushed weighs 1.602 gram per cubic centimeter or 1 602 kilogram per cubic meter, i.e. density of stone, crushed is equal to 1 602 kg/m³.In Imperial or US customary measurement system, the density is equal to 100.0096 pound per cubic …

base materials included Dense Graded Aggregate (DGA), and Crushed Stone Base (CSB). Number 57s, crushed river gravel, recycled concrete, and asphalt drainage blanket samples were submitted for testing by engineers of the Kentucky Transportation Cabinet.

Dense graded crushed stone is available in a number of sizes. Being a crushed stone product and well graded, these products spread and compact quickly. Rail Road Ballast Stone. Lorusso Corporation provides Railroad Ballast Stone that meets all AREMA (American Railway Engineering and Maintenance of Way Association) standards. We provide ...

Table 3602/1 CRUSHED STONE BASE AND SUBBASE: MATERIAL REQUIREMENTS Material TYPE OF MATERIAL Characteristic G1 G2 G3 Parent Sound rock from an approved Sound rock, boulders Sound rock, boulders or ... REQUIREMENTS relative density. bulk relative density. AASHTO density (as specified) TABLE 3402/1 REQUIREMENTS FOR TYPES G4 TO G6 MATERIALS